Bowtie Engineering BBB Business Review

Can Switchgear Maintenance Be Done in a Data Center Without a Full Shutdown?

Quick Answer: Partly. Infrared thermography, ultrasonic inspection and visual checks can be done on energized switchgear with covers closed. Cleaning, mechanical inspection, torquing and electrical testing require the section being worked on to be de-energized and placed in an electrically safe work condition under NFPA 70E Article 120. Data centers avoid a full shutdown by using their redundant design: A and B distribution paths, tie breakers and maintenance bypass let one section be isolated while the other carries the load. Bowtie Engineering supports switchgear maintenance, testing and NFPA 70B-aligned maintenance planning for data centers across the United States. Call 866-730-6620 to plan your next maintenance window.

Data centers cannot simply turn off the building to maintain switchgear, yet NFPA 70B now requires a documented maintenance program and NFPA 70E does not permit routine hands-on work on energized equipment. The answer to the conflict is not to skip maintenance or to work live. It is to use the redundancy the facility was built with, plan the work in sections and do the energized part of the job with the right methods. This article explains which tasks can be done energized, which cannot, how redundant designs make sectional outages possible and how to plan one.

Which Switchgear Maintenance Tasks Can Be Done While Energized?

Energized tasks are those that do not require opening the enclosure or touching conductors. The main ones are:

  • Infrared thermography through infrared windows or on exposed terminations, which finds hot connections, phase imbalance and failing components under real load.
  • Ultrasonic and partial discharge detection, which picks up tracking, corona and arcing inside medium-voltage gear before it fails.
  • Visual and operational checks: indicator status, meter readings, breaker position, audible noise, ventilation, heaters, filters and signs of moisture or pests.
  • Reviewing protective relay event logs and trip unit records.

These tasks are the predictive core of a data center program. Done regularly, they tell you which sections need attention at the next outage and which can wait, which is exactly the condition information NFPA 70B uses to set intervals.

Which Tasks Require the Gear to Be De-Energized?

Anything hands-on. NFPA 70E 110.2(B) requires an electrically safe work condition wherever an electrical hazard exists, and NFPA 70E permits energized work only when de-energizing introduces additional hazards or increased risk, or is infeasible due to equipment design or operational limitations. Being inconvenient for production is not infeasible. Tasks that must be de-energized include:

  • Cleaning insulators, bus and barriers.
  • Inspecting and torquing bus joints and cable terminations.
  • Lubricating and exercising breaker mechanisms, shutters and racking systems.
  • Insulation resistance, contact resistance and primary injection testing.
  • Protective relay testing and calibration where the relay cannot be isolated from its circuit.

Where a task truly must be done energized, 130.3 requires an energized electrical work permit, and the 2027 edition adds in 130.2(A)(2) that when the permit specifies shock or arc flash PPE, a second trained person must be present outside the greater of the limited approach or arc flash boundary. This is a last resort for specific tasks, never a plan for routine maintenance.

How Does a Redundant Design Allow Maintenance Without Dropping Load?

Most data centers are built so that any single piece of distribution equipment can be removed from service while the load stays up. The common patterns are:

  • Dual-corded loads fed from separate A and B paths, so one path can be de-energized while the other carries the full load.
  • Main-tie-main switchgear, where the tie breaker lets one main and its section be isolated while the other main feeds both buses.
  • UPS systems with maintenance bypass, so the UPS and its input or output switchgear can be isolated without interrupting the load.
  • Generator paralleling gear and transfer switches that can carry load while utility switchgear is worked on.

Concurrent maintainability is the design term for this: the ability to maintain any component without affecting the critical load. Maintenance planning starts by confirming, from the one-line diagram, exactly which breakers and switches place a section in a safe state and which path carries the load in the meantime.

How Is a Sectional Switchgear Outage Planned in a Data Center?

A good plan follows a method of procedure (MOP) that the facility and the maintenance provider agree before the window opens. The essential steps:

  1. Confirm the one-line diagram is current and identify every source that feeds the section, including ties, backfeeds and backup sources.
  2. Run an energized infrared and ultrasonic survey first, so the outage work list is prioritized by actual findings.
  3. Transfer load to the redundant path and confirm the load is stable before any isolation.
  4. Open, lock and tag each source following the written lockout/tagout procedure under OSHA 1910.147 and NFPA 70E Article 120, then test for absence of voltage with a rated tester, checked before and after use, and apply temporary protective grounds where the work requires them.
  5. Carry out inspection, cleaning, mechanical checks and tests to the ANSI/NETA Maintenance Testing Specifications, with measured values recorded for every device.
  6. Restore in the reverse order, verify, then transfer load back and repeat for the next section.

Bowtie Engineering’s switchgear maintenance checklist walks through the planning, inspection, cleaning, testing and documentation steps in more detail.

What Safety Controls Apply to the Crew?

Even with the section de-energized, the adjacent sections are live and the available fault current in data center switchgear is high. The crew should work to the arc flash labels, use remote racking where available to stay outside the arc flash boundary, account for stored energy in springs and capacitors, and hold a job briefing covering hazards, energy controls and PPE before each section. The NFPA 70E host and contract employer provisions in Article 110 also apply: the data center must share labels, one-lines and known hazards with the maintenance contractor, and the two must coordinate their lockout/tagout procedures under 1910.147(f)(2).

How Often Should Data Center Switchgear Be Maintained?

NFPA 70B Table 9.2.2 gives baseline intervals by equipment type, manufacturer recommendations take precedence and Section 9.3 adjusts the interval to the equipment condition level. Criticality is one of the condition factors, so switchgear feeding a critical load tends toward more frequent attention. In practice most data centers run energized predictive surveys at least annually and schedule de-energized maintenance per section on a multi-year rotation set by condition, with any section showing a major infrared discrepancy (the ANSI/NETA specifications treat more than 15 degrees C between similar components under similar load as requiring immediate repair) moved to the front of the queue.

What Should a Data Center Ask a Switchgear Maintenance Provider?

Ask whether the provider can survey energized, help plan the outage around your operations, perform the de-energized work and testing, and document everything in one coordinated engagement. Ask how they test breakers (primary injection, not only secondary), whether the technicians are NETA-certified and NFPA 70E trained, and how findings feed back into the arc flash study. Bowtie Engineering’s electrical maintenance services include switchgear maintenance, infrared thermography and NETA-standard testing, with testing that requires de-energization coordinated with your facility team and planned outage windows. For service-contract clients, results load into the BowVue platform. The ANSI/NETA standards define the tests and acceptance values the work should be measured against.

Frequently Asked Questions

Is infrared thermography enough on its own for data center switchgear?

No. Infrared finds heat-related problems under load, but it cannot clean insulators, lubricate mechanisms or verify breaker trip times. It is the tool that decides what the next de-energized outage must address.

Can a data center justify energized work because downtime is costly?

Not under NFPA 70E. The standard limits energized work to cases where de-energizing creates additional hazards or increased risk, or is infeasible due to equipment design or operational limitations. Cost and inconvenience are not infeasibility, and redundant designs exist precisely so maintenance can be done safely.

What is a method of procedure (MOP)?

A step-by-step written plan for a specific maintenance activity in a critical facility, covering the load transfers, isolations, verifications, work steps, restoration and rollback. It is agreed by the facility and the contractor before the work window.

How long does a sectional switchgear outage take?

It depends on the number of sections, the tests required and how the load can be transferred. A provider should give a schedule with the quote so the window can be planned with operations.

Does maintenance change the arc flash labels?

It can. If maintenance changes a protective device setting or shows a breaker operating outside tolerance, the arc flash study and labels for that equipment should be reviewed, as NFPA 70E 130.5 requires after a major modification.

Key Takeaways

  • Infrared, ultrasonic and visual checks can be done on energized data center switchgear; cleaning, torquing and testing cannot.
  • NFPA 70E 110.2(B) and 130.2 require an electrically safe work condition for hands-on work; cost and inconvenience do not justify energized work.
  • A and B paths, main-tie-main gear and maintenance bypass allow one section to be isolated while the load stays up.
  • A written method of procedure, current one-line and lockout/tagout under OSHA 1910.147 are the backbone of a sectional outage.
  • NFPA 70B sets intervals by equipment type and condition, with criticality pushing data center gear toward more frequent attention.
  • Bowtie Engineering supports switchgear maintenance and testing for data centers; request a maintenance quote.

By John Welch, P.E., C.E.M.

John Welch is the Founder and CEO of Bowtie Engineering, a licensed Professional Electrical Engineer and Certified Energy Manager. His work focuses on electrical safety, incident energy studies, training and electrical maintenance. John co-hosts the Electrical Safety Talks podcast.